Plywood for laser cutting – produced from birch timber, internal, based on urea and formaldehyde resins.
Produced from hardwood (100% birch), interior on the basis of urea-formaldehyde or exterior with white glue line on the basis of melamine-urea-formaldehyde resins.
The quality classes of these types of plywood are B/BB and BB/BB, and the internal layers are flawless.
Plywood is composed of 1 mm thick veneers by cross bonding. Face veneers can be both long grain and cross grain.
The inside veneers are selected to minimize wholes and big knots. Plywood is bonded with a MR glues that does not burn in the flame of laser.
It is available in two types: both with, and without, double-sided transparent melamine foil.
These types of plywood hold E1 sanitary attestation.
Plywood is perfectly made for being cut and engraved with a laser system
Smooth und precise cutting edges
The surfaces remain crack-free and do not show signs of bruise by clamping
High repeatability and accuracy of fit for example for intarsias
Narrow cutting edges in the area of 1/10 mm, therefore almost no thermical influence
Laser cutting of extremely fine contours and practically radius-free inner contours
Engraving of reliefs
For this purpose we have special designed plywood high quality veneers in the whole section uniform structure non-flammable glue strict size tolerances straightness available with additional overlays. It is the highest quality birch plywood with uniform structure through the whole section. It can be delivered as a raw plywood or lacquered on one or both sides. Laser plywood is designed for precise laser cutting. Plywood is composed of 1 mm thick veneers by cross bonding. Face veneers can be both long grain and cross grain.
Thicknesses mm : 12; 15; 18; 21
Size mm : 1525 x 1270
Long grain plywood panels with the length up to 1525 mm are also available.
Cut to size panels and machining available in accordance with the customers’ requirements.
Grade : I/II , II/II
Glue type : MR, Urea Carbamide (Interior),
Quality References : INTERGOVERNMENTAL STANDARD GOST 3916.1-96
Edges : Processing by waterproof acrylic paint
Formaldehyde emission : E1,
Moisture content : max 10 %
Density : (depending on thickness) 450 kg/m³ ± 5 % EN 323
Wood species : 100% birch Further Processing
Laser plywood can be lacquered, cut to size or drilled according to customers wish.
Protective lacquering – two layers of primer are applied over the surface by roller coating method, each layer is about 15 – 20 g/m².
The final surface is transparent and slightly rough.
Elevated quality layer – two layers of primer are applied over the surface by roller coating method, each layer is about 15-20 g/m², then finish layer of lacquer 80-100 g/m².
Plywood is sanded after priming that gives absolutely smooth and shining surface of the final product. Edges of the panel can be also sealed with lacquer.
Uniform structure, non-flammable glue, environmentally friendly, durable, easy workable.
Laser plywood transparent offers the following advantages
smooth, semi gloss surface
hygienic and easy to clean
taint and odour free surface
low water permeability
Laser plywood transparent is smooth faced birch plywood specially glued for laser cutting. The board is coated on both sides with a hard wearing transparent melamine film, which protects effectively the surface from moisture pick up and also makes it easy to keep the die board clean.
Laser plywood transparent is an ideal material for demanding dies. Strong and homogeneous birch cuts well with a laser, is accurate and holds the knives firmly in place. The thin veneer multilayer construction ensures that the board stays flat when properly handled and stored.
Laser plywood boards are best suited for
die boards, stripping and blanking tools, laser cutting, printing blocks
plotter production , poligraphy , furniture , toys
Laser plywood is also available without the melamine film.